Hayward Flow Switch Install

The flow switch should be installed horizontally and must not be installed upside down. This kit includes the tee, the flow sensor with cable and 2 unions.

Pin On Featured Products

The flow switch is a safety device that ensures water is flowing through the cell before the automation control unit begins to generate chlorine.

Hayward flow switch install. Make sure that full flow is achieved (no air in the system) and run the pump for at least 15 seconds. Needed when installing an aqua rite cell when purchased with a pro logic system. Do not leave it like that.

Install the pipe fitting into your flow t, make a mark on it to indicate flow direction, then remove it. Mount the magnet on your flexible flapper arm. Synchronization instruction after installation of the actuator(s), they may need to be synchronized.

Hayward strongly recommends that the manual be read by the installer before installing the swimming pool/spa/ hot tub heater. Material supplied or workmanship performed by others in process of installation. It must be positioned as instructed by the arrow sticker adhered to it marking the water flow direction through the tee.

A flow switch is required if using chemistry sense and dispense accessories. If the guide can not be applied to your particular installation, refer to the additional information in this manual. Used to upgrade pro logic or aqua logic to add a salt water generator.

Arrow on switch indicates the direction of water flow, ensuring proper installation; Although this hayward flow switch is simple to install, it is imperative that it is properly connected. You can use an old phone plug with the wires twisted together to simulate a closed flow switch.

Unplug the flow switch from the unit and see if you get a no flow light. Hayward flow control products and solutions are used in a wide variety of applications and installations worldwide. Service support center (61 whitecap road, north kingstown ri, 02852) or visit the hayward web site at www.hayward.com.

Use this guide if possible. Functioning suction outlets per pump must be installed. Floor or wall), must be installed a minimum of three feet (3’) [1 meter] apart, as measured from near point to near point.

Best location for the flow switch is on the return line going back to the pool, if you have a pool & spa system the flow switch t should be located in the line where water goes back to the pool, not the spa. If the light is on steady, then it thinks that the flow switch is open. Following heater installation, the installer should leave the manual with the consumer for future reference.

Replace cover and handle and tighten screws and locking knob. Epoxy the flapper arm and reed switch to the pipe fitting in such a manner that water flow in the direction marked. Check that the flow switch is plugged into the connector on the bottom of the control unit and that the wire is not cut or damaged.

Use only hayward genuine replacement parts 6 The flow switch calibration procedure is complete. If yes the flow switch is bad.

Hayward pro logic union kit is a factory original replacement part. 6 month manufacture parts only warranty when purchased through a hayward authorized online reseller. The flow switch should be located in a pvc t and the arrow needs to be pointed the same direction as the water flow.

The switchbox is available in two sizes. Made of industrial grade thermoplastics, our products deliver superior corrosion and chemical resistance, as well as insuring purity of media, versus traditional metal based flow control products. If the switch is downstream of the cell, the cells length can be counted as part of the required 12 inches.

Suction outlets in the same plane (i.e. Generic replacement for model numbers: Turn the filter pump off.

• dual suction outlets shall be placed in such locations and distances to. Turn the filter pump on. Fits hayward® and goldline® saline generating systems;

This may cause debris to settle inside the tess and restrict the paddle movement. Attach wires to either end of reed switch to connect back to controls. Mountinq the switchbox to a valve:

You can now turn on your filter There is a notch on the side that we determined must the it’s version of an arrow. Hello shawn, yes based on the information provided that would mean a new flow switch should be installed.

I think the question if you can answer it, hayward, is whether the rj version can just have a flow switch added and have it work or if the software does not support it. However the item did not have an arrow clearly showing the correct way to install the item to match the flow of the water. The switch can be mounted on either side of a chlorine cell, but it must be attached by at least 12 inches of straight pipe.

The salt & swim should now display a solid inadequate water flow and a solid standing by led. Put toggle switch back to on1 or on2 position. The flow switch light will blink for about 30 seconds from the time it detects a closed flow switch and then the light should go out.

System startup and firmware upgrade (page 22) the most common installation technique is described in the included quick start guide. Damage resulting from improper installation including installation on pools larger than the product rating. Flow switch (not included) an optional flow switch can be used to detect leaks or clogs in the pool/spa plumbing.

How To Replace A Jandy Temperature Sensor Sensor Temperatures Spice Things Up

Pin On The Pool Guys How To Videos

Finally Plumbed My Agp With Pvc Pvc Pool Pool Plumbing Pool Hoses

Pentair Intellichlor External Power Supply 521171 Power Supply Pool Supplies Power

Haywards Stainlesssteel Niches Are Built From Solid Non-corrosive Stainless Steel Pool Light Pool Supplies Led Pool Lighting

Youtube Instructional Video Cleaning Cell

Flow Switch Installation For An Aquarite Salt System Flow System Installation

Pin On The Pool Guys How To Videos

Hayward Goldline Pkit Flow Switch P-kit Pool Supply 4 Less Portable Spa Pool Supplies Pool Accessories

How To Clean Your Salt System System Cleaning Pool

Pin On Cars Bikes Repair

Convert Electronic Water Heater To Mechanical Heater Httpwaterheatertimerorghow-to-convert-energy-smart-water-heater-to-o Water Heater Smart Water Heater